Guide 8 of 8 · Practice
How to Animate a Walk Cycle: The Four Key Poses Explained
Contact, down, passing and up: the four poses behind every walk, with timing and loop tips.
Short answer
A walk cycle is a looping set of drawings built from four key poses per step (contact, down, passing and up), mirrored for the second step, usually timed at about 12 frames per step at 24 fps.
Key takeaways
- Every step in a walk has four key poses: contact, down, passing and up.
- The second step mirrors the first with the legs and arms swapped, so a full cycle has two steps.
- About 12 frames per step at 24 fps gives a normal pace; fewer frames read as a hurry, more as a stroll.
- The body is lowest in the down pose and highest in the up pose, and that bob is what gives a walk weight.
After the bouncing ball, the walk cycle is the next exercise most animators take on. It combines everything the ball taught you about weight and spacing with a body that has to stay balanced. It is also one of the most reusable things you will ever animate, because a single good cycle can loop for as long as a shot needs.
This guide covers a basic side-view walk built from key poses. The approach works the same way with paper, frame-by-frame software or a rigged character.
What is a walk cycle?
A walk cycle is a short sequence of drawings showing two steps that loops back on itself, so a character can walk for any length of time.
A full cycle has two steps: one led by the left foot and one led by the right. The last frame flows straight into the first, so playing it again and again produces continuous walking. You can animate it in place, with the background scrolling behind, or move the character across the screen.
Each step is built from the same set of key poses. Once you have one step, the second is mostly a mirror of the first.
What are the four key poses of a walk?
The four key poses are contact, down, passing and up, and each one has a specific job in carrying the body's weight forward.
| Pose | What happens | Body height |
|---|---|---|
| Contact | Both feet touch the ground: front heel down, back toe about to lift | Middle |
| Down | The front leg bends and takes the weight | Lowest |
| Passing | The back leg swings past the standing leg | Middle, rising |
| Up | The standing leg pushes off and the body rises before falling into the next step | Highest |
The contact pose shows the widest stride. In the down pose, the body sinks as the front knee absorbs the impact. In the passing pose, the free leg swings under the body, roughly level with the knee of the standing leg. The up pose comes just before the next contact, with the body at the top of its arc and the free foot reaching forward.
Then the cycle repeats with the other leg leading.
How many frames does each step need?
At 24 fps, about 12 frames per step is a normal walking pace, which makes a full two-step cycle about one second long.
With 12 frames per step, a simple layout puts contact on frame 1, down on frame 4, passing on frame 7 and up on frame 10, with the next contact on frame 13. The second step follows the same pattern from 13 to 24, and frame 25 equals frame 1 again.
Change the count to change the mood:
- 8 to 10 frames per step reads as hurried or determined.
- 12 frames per step reads as an ordinary walk.
- 16 frames or more per step reads as slow, tired or relaxed.
These are starting points. The frame rates and timing guide explains how to count frames and work on ones or twos.
How should the body move up and down?
The hips drop in the down pose and rise in the up pose, tracing a gentle wave that gives the walk its weight.
Track a single point on the hips through the cycle and it should move along a wave: middle at contact, lowest at down, rising through passing, highest at up, and back to middle at the next contact. The head follows the same wave with a slight delay.
This vertical bob is what separates a walk from a slide. Keep it subtle for a normal walk. Exaggerate it for a bouncy, cartoon walk or a heavy, plodding character. You can test the rhythm of the bob on its own in the keyframe playground by keying a ball through four heights and adjusting the easing until the rise and fall feel natural.
What do the arms and shoulders do?
The arms swing opposite to the legs, so when the left leg is forward, the right arm is forward.
This counter-swing comes from the twist of the body. As the hips rotate to bring one leg forward, the shoulders rotate the other way to keep balance. The arms are farthest forward and back in the contact pose and pass the body around the passing pose.
Let the hands lag a little behind the elbows, and the elbows a little behind the shoulders. This overlapping action keeps the arms from swinging like rigid sticks. The keyframes and in-betweens guide explains how breakdowns between keys create this kind of lag.
How do you stop the feet from sliding?
The planted foot must stay locked to the ground from contact until it lifts, or move back at a perfectly even rate if the character walks in place.
Sliding feet are the most visible walk cycle error. Two setups avoid it:
- Walking across the screen. The character's body moves forward, and the planted foot stays at exactly the same spot on the ground until it lifts off. Mark the spot on your paper or canvas and check every frame.
- Walking in place. The body stays centered, and the planted foot moves backward by the same distance each frame. The background scrolls at that same speed so the foot appears fixed to the ground.
If the planted foot moves unevenly, the character will look like they are skating or slipping.
How do you make the loop play smoothly?
Make the last frame lead into the first without repeating it, and check that every part of the body returns to its starting position.
A common mistake is drawing the final contact pose as an exact copy of frame 1 and including it in the loop. That doubles the frame and causes a small hitch every cycle. The cycle should end on the frame before the repeat.
Play the loop many times in a row and watch one body part at a time: the head, then the hips, then each hand. Any part that jumps at the loop point needs adjusting. Onion skin helps here, because it shows the spacing between neighboring frames and makes uneven gaps easy to spot.
Where should you go after a basic walk?
Once a plain walk works, change one thing at a time: the timing, the bob, the posture or the arm swing.
Try a sneak with exaggerated up poses, a tired shuffle with almost no bob, or a proud strut with the chest forward. Each one uses the same four poses with different spacing and posture, which is a good way to see how much character comes from timing alone.
Questions
- How many frames is a walk cycle?
- A common starting point is 24 frames for a full cycle at 24 fps, which is 12 frames per step and one second per stride. A brisk walk might use 8 to 10 frames per step and a slow stroll 16 or more.
- Which pose should I draw first?
- Draw the contact pose first. It sets the stride length and the character's height, and the other poses are measured against it. Then draw the passing pose, then the down and up poses.
- Why does my walk cycle look like the character is skating?
- The foot on the ground is probably sliding. On a cycle where the character walks in place, the planted foot must move backward by the same distance on every frame. If the character crosses the screen instead, the planted foot must stay locked to one spot until it lifts.
- Do the arms swing with the same side leg?
- No. The arms swing opposite to the legs. When the left leg is forward, the right arm is forward. This counter-swing balances the twist of the hips and shoulders.